ATP3330-超薄、超高分辨率、M型光路光纖光譜儀
產品概述
ATP3330和ATP5330是奧譜天成新開發的一款超薄、制冷型、超高分辨率微型光譜儀,ATP3330和ATP5330是基于奧譜天成自主研發的M型光路結構,具有非凡的超高分辨率;同時,它采用制冷的2048或4096像素線陣探測器,達到了的超高分辨率,分辨率可達0.05nm,適用于各種高分辨率應用場合,同時具備高可靠性、超高速、低成本、高性價比等特性,可適應在線測試等各種環境用途的微型光譜儀。
ATP3330為非制冷的,ATP5330則采用TEC電制冷,制冷溫度-5℃,大大降低了光譜儀的暗電流和噪聲,提高了光譜儀的動態范圍和信噪比,同時提高了光譜儀的環境適應性。ATP5330P則采用制冷背照式CCD,信噪比更優。
ATP3330和ATP5330可接收SMA905光纖輸入光或者自由空間光,通過USB2.0或者UART端口,輸出測量所得的光譜數據。
ATP3330只需要一個5V直流電源供電或直接從USB接口取電,非常便于集成使用。ATP5330則需要額外的5V電源。
探測器制冷? | 探測器像素 | |
ATP3330 | 否 | 2048 |
ATP3334 | 否 | 4096 |
ATP5330 | 是,-5℃ | 2048 |
ATP5334 | 是,-5℃ | 4096 |
ATP5330P | 是,-10℃,背照式CCD | 2048 |
特征
Ø M型光路,更高分辨率;
Ø 光譜范圍: 200-1100 nm;
Ø 光譜分辨率: 0.05 ~ 3 nm;
Ø 光路結構: 非交叉C-T;
Ø 檢測器: 2048或4096像素;
Ø 探測器制冷溫度:-5 ℃
Ø 積分時間: 0.1ms ~ 256s;
Ø 供電電源: 直流5V 供電;
Ø ADC位深:16位;
Ø 數據輸出接口:USB Type-C;
Ø 20針擴展接口;
應用領域
Ø LIBS、等離子體發光檢測;
Ø 拉曼光譜檢測;
Ø 波長監測,激光、LED等發光體
Ø 水質分析儀
Ø LED分選機、顏色檢測;
Ø 光譜分析、輻射分光分析、分光光度分析
Ø 反射、透射光譜檢測
3 Electrical Pin-out
Table 1 Electrical Characteristics
Parameter | Min | Typ | Max | Unit |
Power Supply | ||||
Operating voltage range | 4.5 | 5 | 5.5 | V |
Operating current | 170 | mA | ||
Logic Inputs(3.3V LVTTL, Five-volt tolerant) | ||||
High level input voltage | 1.7 | 3.6 | V | |
Low level input voltage | -0.3 | 1.0 | V | |
Logic Output(3.3V LVTTL) | ||||
High level output voltage | 2.4 | V | ||
Low level output voltage | 0.4 | V |
The module is equipped with a 30-pin male angled box header(2x15, 2.00 mm pitch) and Type-C interface.
Table 2 Electrical Pin-Out
Pin# | Description | I/O | Function Description |
1 | VCC | / | Power Supply, 5V±0.5, |
2 | GND | / | Ground |
3 | UART_TX | Output | UART Transmit signal |
4 | UART_RX | Input | UART Receive signal |
5 | Lamp_En | Output | LVTTL output the lamp enable signal. |
6 | Continuous_strobe | Output | LVTTL output the continues strobe signal. |
7 | Ext_trigger_in | Input | LVTTL input the trigger signal. |
8 | Single_strobe | Output | LVTTL output the single strobe signal. |
9 | SPI_SCK | Output | The SPI Clock signal for communications to other SPI peripherals |
10 | SPI_MOSI | Output | The SPI Master Out Slave In (MOSI) signal for communications to other SPI peripherals |
11 | SPI_MISO | Input | The SPI Master In Slave Out (MISO) signal for communications to other SPI peripherals |
12 | SPI_CS | Output | The SPI Chip/Device Select signal for communications to other SPI peripherals |
13 | GPIO0 | Input /Output | General Purpose Software Programmable Digital Inputs/Outputs, LVTTL Logic. |
14 | GPIO1 | Input /Output | General Purpose Software Programmable Digital Inputs/Outputs, LVTTL Logic. |
15 | GPIO2 | Input /Output | General Purpose Software Programmable Digital Inputs/Outputs, LVTTL Logic. |
16 | GPIO3 | Input /Output | General Purpose Software Programmable Digital Inputs/Outputs, LVTTL Logic. |
17 | GPIO4 | Input /Output | General Purpose Software Programmable Digital Inputs/Outputs, LVTTL Logic. |
18 | GPIO5 | Input /Output | General Purpose Software Programmable Digital Inputs/Outputs, LVTTL Logic. |
19 | GPIO6 | Input /Output | General Purpose Software Programmable Digital Inputs/Outputs, LVTTL Logic. |
20 | GPIO7 | Input /Output | General Purpose Software Programmable Digital Inputs/Outputs, LVTTL Logic. |
4 Order Guide
Order number Rules:
Model | Spectral region | Slit width | ||
ATP5030 | Short wavelength | Long wavelength | Slit width |
For example:
What to buy ATP5030, spectral region: 200-1000nm, slit width is 50 um, then the order no is:
ATP5030-200-1000-050
Order No | Spectral region | Slit | |
ATP5030-200-400-### | 200~400 | 10 μm 25 μm 50 μm 100 μm 200 μm Other:______μm | |
ATP5030-200-850-### | 200~850 | ||
ATP5030-200-1000-### | 200~1000 | ||
ATP5030-340-850-### | 340~850 | ||
ATP5030-600-1100-### | 600~1100 | ||
ATP5030-###-###-### | Other |