污水處理設備 污泥處理設備 水處理過濾器 軟化水設備/除鹽設備 純凈水設備 消毒設備|加藥設備 供水/儲水/集水/排水/輔助 水處理膜 過濾器濾芯 水處理濾料 水處理劑 水處理填料 其它水處理設備
東莞市超順機電設備工程有限公司
東莞市超順機電設備工程有限公司
| 參 考 價 | 面議 |
產品型號
品 牌
廠商性質其他
所 在 地東莞市
聯系方式：歐先生查看聯系方式
更新時間：2025-02-24 12:23:16瀏覽次數：65次
聯系我時，請告知來自 環保在線小魚干包裝機小魚干包裝機--剛性真空封口機有旋蓋封口機、滾邊封口機、滾紋封口機、壓塞封口機、壓蓋封口機、卷邊封口機等
小魚干包裝機
小魚干包裝機--剛性真空封口機有旋蓋封口機、滾邊封口機、滾紋封口機、壓塞封口機、壓蓋封口機、卷邊封口機等。不一樣的封口機可以結束不一樣類型商品的封口，跟著真空封口機品種的增多，在工作中的運用也越來越廣泛。在封口機運用進程中經常會碰到這樣那樣的缺陷，下面超順設備小魚干包裝機為你掃盲真空封口機運用進程中常見的缺陷。
（1）封口不牢，發生缺陷的緣由是冷壓膠輪壓力不合適，熱封速度過快，熱封溫度缺乏，熱封薄膜質量有問題，遇到這種狀況可適當提高熱封溫度，再降低熱封速度，一起加大冷壓膠輪的壓力。
（2）溫度表閃現失靈，封口溫度失控，熱封溫度不穩定，封口處不是被燒焦，就是封合不牢，封口變形，很丑陋，構成該缺陷首要緣由是溫度計已壞，有必要修補；別的，熱電耦可以也壞了，不能正常地將感應溫度傳至溫度計上。換上同類型、同標準的熱電耦即可。
（3）封口機走走停停，速度不一致，構成缺陷的緣由首要是電動機的軸桿聯接處與變速箱聯接處呈現掉落、松懈表象，從頭緊固螺絲，使之悉數符合，問題也就處理了。
（4）封口處呈現不規則痕紋及氣泡，此類缺陷較為常見，首要是因為冷壓膠輪上有擺放不規則的凹凸痕跡，直接反映到包裝上，使封口處呈現較多的顯著痕紋，設備運用時刻長了，高溫帶上附著了塵埃及塑料屑等臟物，構成高溫帶不光滑、不平坦，使得封口受熱不均勻，經冷壓輪壓合后呈現氣泡。交流冷壓膠輪，清洗或從頭交流高溫帶即可打掃。
搜索關鍵詞：小魚干包裝機
Small fish dry packing machine
Small fish, dry rigid vacuum packaging machine, sealing machine screw cap sealer, flange sealing machine, rolling machine, pressure sealing machine, capping, edge sealing machine, etc. Different sealing machine can end of the sealing of different types of goods increased with vacuum sealing machine varieties, also more and more extensively used in our work. In sealing machine use process we often encounter this or that kind of defects, the following super paramagnetic equipment dry fish packing machine for literacy vacuum sealing machine you use in the process of common defects.
(1) the sealing not firm, is the cause of the defect of cold pressing roller pressure is not appropriate, heat sealing speed too fast, the lack of heat sealing temperature, heat sealing film quality has a problem, meet this kind of condition can be appropriately raise heat sealing temperature, and then reduce the heat sealing speed, with increasing of cold pressing roller pressure.
(2) the thermometer flash failure, the sealing temperature control, heat sealing temperature is not stable, pincer-like device isn't burned, is not firm sealing, sealing deformation, very ugly, constitute the primary reason for the defects is thermometer is bad, it is necessary to repair; Other, thermoelectric coupling was broken, can not be normally would transmit the induction temperature to the thermometer. Can be changed into the same type, same standard thermocouple.
(3) the machine stops, the speed is not consistent, constitute a defect reason first is the motor shaft rod coupling and transmission connection place appear to drop, lax appearances, fastening screws from the ground up, all conform to, problems are dealt with.
(4) an irregular mark lines and bubble pincer-like device, this kind of defect is common, first because of cold pressing roller are put on irregular concave and convex, directly reflect the packaging, make the pincer-like device presents more significant mark lines, and equipment use time long, high-temperature belt and plastic scraps on the dust dirt, a thermal zone not smooth, not smooth, makes the sealing heat unevenly, after cold pressing wheel pressing the air bubbles. Exchange of cold pressing roller, clean or communication from thermal belt can be clean.
Search keywords: fish dry packing machine
您感興趣的產品PRODUCTS YOU ARE INTERESTED IN
環保在線 設計制作，未經允許翻錄必究 .? ? ?
請輸入賬號
請輸入密碼
請輸驗證碼
