污水處理設備 污泥處理設備 水處理過濾器 軟化水設備/除鹽設備 純凈水設備 消毒設備|加藥設備 供水/儲水/集水/排水/輔助 水處理膜 過濾器濾芯 水處理濾料 水處理劑 水處理填料 其它水處理設備
上海先鋒閥門廠
會員1.png)
上海先鋒閥門廠
| 參 考 價 | 面議 |
產品型號
品 牌
廠商性質經銷商
所 在 地
聯系方式：經理查看聯系方式
更新時間：2024-10-08 08:16:51瀏覽次數：54次
聯系我時，請告知來自 環保在線性能規范 Property specification用途及特點Purpose and characteristic伸縮蝶閥適用于溫度≤80℃，公稱壓力≤1.6MPa的食品，醫藥、化工、石油、電力、輕紡、造紙等給排水、氣體管道上作調節流量和截流介質的作用，具有補償管道熱脹冷縮的功能。其主要特點如下：1、設計新穎、合理、結構、重量輕、操作方便、啟閉迅速；2、伸縮蝶閥除了能作調節和截流作用、補償管......
性能規范 Property specification
用途及特點Purpose and characteristic
| 伸縮蝶閥適用于溫度≤80℃，公稱壓力≤1.6MPa的食品，醫藥、化工、石油、 電力、輕紡、造紙等給排水、氣體管道上作調節流量和截流介質的作用， 具有補償管道熱脹冷縮的功能。其主要特點如下： 1、設計新穎、合理、結構、重量輕、操作方便、啟閉迅速； 2、伸縮蝶閥除了能作調節和截流作用、補償管道溫差所產生的熱脹冷縮功能外， 還能為安裝更換、維修閥門提供方便； 3、密封部位可調節更換，密封性能可靠等特點。 | Telescopic butterfly valve is suitable for water supplying and draining,gas pipe as adjust flux and cut off medium in foodstuff,pharmacy,chemcal industry,petroleum ,electric power,light textile,paper making etc,with temperature ＜80℃,nominal pressure＜1.6Mpa.and has function of compensation pipe expand with heat and contract with cold,the main characteristic as below: 1.Novel and reasonable design,particular configuration,light and easy to operate and start and stop rapidly. 2.Besides adjust and cut off currency,compensate temperature differential in pipe, which cause ftunction of expansion with heat and extra ction with cold,flexible butterfly valve can provide convenience for installation exchange,maintenance. 3.It has characteristic of hermetical components can adjust and replace, reliable hermetic capability etc. |
設計標準Design standard:GB/T 12238-1989
法蘭連接尺寸Fiange connection dimension:GB/T 9113.1-2000;GB/T 9113.2-2000
GB/T 9115.1-2000;GB/T 9115.2-2000
壓力試驗Pressure test:GB/T 13927-1992;JB/T 9092-1999
主要技術參數 Main technical parameter
| 公稱通徑Nominal diameter | DN(mm) | 50~2000 | ||
| 公稱壓力Nominal pressure | PN(MPa) | 0.6 | 1.0 | 1.6 |
| 試驗壓力 Ps(MPa) Test pressure | 強度試驗Strengh test | 0.9 | 1.5 | 2.4 |
| 密封試驗Seal test | 0.66 | 1.1 | 1.76 | |
| 氣密封試驗Gas seal test | 0.6 | 0.6 | 0.6 | |
| 適用溫度Applicable temperature | ≤80℃ | |||
| 適用介質Applicable medium | 空氣、水、蒸氣、煤氣、油品等。Air,water,steam,coal gas,oil. | |||
| 驅動形式Drive modality | 手動、蝸桿蝸輪傳動、氣傳動、電傳動。hand,worm wheel drive,pneumatic drive,electric drive. | |||
主要零件的材質Material for main parts
| 零件名稱Parts name | 材料Material |
| 閥體Body | 鑄鐵、鑄鋼、不銹鋼、鉻鉬鋼、合金鋼Castiron,cast steel,stainless steel,Cr.Mo.Steel.alloy steel |
| 蝶板Disc | 鑄鋼、合金鋼、不銹鋼、鉻鉬鋼Cast steel,Alloy steel,stainless steel,Cr.Mo.Steel |
| 密封圈Seal ring | 橡膠、聚四氟、聚內脂、不銹鋼Rubber,Telflon,polyester alctone,stainless steel |
| 閥桿Stem | 2Cr13、不銹鋼、鉻鉬鋼Stainless steel,Cr.Mo.Steel |
| 伸縮管Flexible tube | 鑄鐵、鑄鋼、不銹鋼、鉻鉬鋼Cast iron,cast steel,stainless steel,Cr.Mo.Steel |
| 填料Packing | 柔性石墨Flexible graphite |
伸縮蝶閥安裝使用注意事項Notice for installation and usage of telescopic butterfly valve
1、伸縮蝶閥在安裝前必須平放，切勿隨意磕碰。
2、伸縮媒閥出廠時結構長度為最小長度，安裝時，拉至安裝長度（即設計長度）。
3、當管道間長度超過伸縮閥安裝長度時，請調整管道間屬，切勿強行拉行伸縮閥，以免損壞伸縮閥。
4、伸縮蝶閥可在任意位置安裝，做溫度補償用時，在管道安裝完成后，需沿管道軸線方向兩端加支架，防止伸縮閥伸縮管拉出（見圖1），支架的支承力按下列公式計算，運行時嚴禁將支架卸掉。
F＞π/4PS·DN2·（kgf）
式中：PS-管道試驗壓力，DN-管道直徑
5、伸縮蝶閥不做溫度補償時，只做安裝更換、維修閥門方便用時，可用通螺栓限位，對稱夾緊伸縮蝶閥以防止伸縮管拉出（見圖2），損壞伸縮蝶閥及管道裝置或建筑物。螺檢直徑可按照法蘭螺栓直徑。其螺栓強度和承受試驗壓力及管道拉力，按上公式進行計算，運行時限位螺栓嚴禁卸掉（螺栓另配）
6、管道施工現場嚴禁隨意拆卸解體伸縮蝶閥。
7、本伸縮蝶閥，加工精細，配合嚴密，請勿在現場隨意反復拉長壓短伸縮蝶閥。管道安裝時，要求伸縮閥兩端管道必須同心，管道上的兩法蘭面要求平行。
8、法蘭固定螺栓應對稱緊固，請勿單邊強行緊固法蘭固定螺栓。
9、伸縮管安裝在閥門后。
10、伸縮閥伸縮部分不得安裝在管道拐角處或管道未端。
1.Telescopic butterftly valve should be placed horizontaly,any colision will be not allowed.
2.When telescopic buerfly valve left factory,its structure length is the minimum length,when installation should be pulled to installation length(Design length)
3.When length between pipes exceed telescopic valve installation length,please adjust the space between pipes,shouldn't pull telescopic valve constrainedly,lest damage telescopic valve.
4.Telescopic butterfly valve can be installed in optional position,when it compensate temperature,after install pipe,it should be installed brackets on both sides of pipe axes direction,in order to prevent telescopic tube of telescopic valve from pulling out(see diagram1),accumulate supporting force of bracket should be according to formula as below,andshouldn't unload bracket when delivery.
F＞π/4PS·DN2·（kgf）
Test:PS-pipe pressure test,DN-Diameter of pipe
5.When telescopic butterfly valve doesn'ttreat as temperature compensation,only treat as install,exchange,and maintain valve conveniently,and it can use
screw to retain,symmetry clamp telescopic butterfly valve symmetrically,so as to avoid telescopic tube being pulled out(see diagram2),and damage
telescopic butterfly valve and pipe fitting or consruction,Diameter of bolt can according to diameter of flange bolt,accumulate bolt intensity and
bearing pressure test and pull of pipe according to above formula,when operation,retaining screw should not be unloaded(mate in addition)
6.On pipe constructive spot where remove or disassenbly telescopic buttdrfly valve wil be not allowed.
7.This kind of telescopic butterfly valve has been machining and fitting strictly,don't pull and press it from tine to time optionally on spor.when install
pipe,Botn pipe ends of telescopic valve snouldbe homocentric,botn facing flanges should be horizontal.
8.Fixed bolt on flange should be symmetrical and clamped,shouldn't calamp fixed bolt of flange on single side.
9.Telescopic tube should be installde behind of valve.
10.Telescopic part of telescopic valve shouldn't be installed on corner of pipr or end of pipe.
您感興趣的產品PRODUCTS YOU ARE INTERESTED IN
進口蝸輪法蘭旋塞閥 進口旋塞閥德國羅博特RBT品牌
進口蝸輪法蘭旋塞閥 進口旋塞閥德國羅博特RBT品牌 面議
環保在線 設計制作，未經允許翻錄必究 .? ? ?
請輸入賬號
請輸入密碼
請輸驗證碼
