污水處理設備 污泥處理設備 水處理過濾器 軟化水設備/除鹽設備 純凈水設備 消毒設備|加藥設備 供水/儲水/集水/排水/輔助 水處理膜 過濾器濾芯 水處理濾料 水處理劑 水處理填料 其它水處理設備
廈門慧嘉生物科技有限公司
會員1.png)
廈門慧嘉生物科技有限公司
暫無信息 |
閱讀：227發布時間：2013-5-17
Porcine myelin basic
protein,MBP
ELISA Kit
This immunoassay kit allows for the in vitro rapid detection of porcine MBP
concentrations in serum, plasma.
Expiration date six months from the date of manufacture
FOR RESEARCH USE ONLY. NOT FOR USE IN DIAGNOSTIC PROCEDURES.
2
PRINCIPLE OF THE ASSAY
This assay employs the competitive inhibition enzyme
immunoassay technique. The microtiter plate provided in this kit
has been pre-coated with goat-anti-rabbit antibody. Standards or
samples are added to the appropriate microtiter plate wells with
an antibody specific for MBP and Horseradish Peroxidase （HRP）
conjugated MBP, then incubated. Then substrate solutions are
added to the wells, respectively. The enzyme-substrate reaction
is terminated by the addition of a sulphuric acid solution and the
color change is measured spectrophotometrically at a
wavelength of 450 nm ± 2 nm. The concentration of MBP in the
samples is then determined by comparing the O.D. of the
samples to the standard curve.
DETECTION RANGE
The standard curve concentrations used for the ELISA’s were 10
ng/ml, 5 ng/ml, 2 ng/ml, 1 ng/ml, 0.5 ng/ml.
SPECIFICITY
This assay recognizes porcine MBP. No significant
3
cross-reactivity or interference was observed.
SENSITIVITY
The minimum detectable dose of porcine MBP is typically less
than 0.25 ng/ml.
The sensitivity of this assay, or Lower Limit of Detection （LLD）
was defined as the lowest protein concentration that could be
differentiated from zero.
MATERIALS PROVIDED
Reagent Quantity
Assay plate 1
Standards （S1-S5） 5 x0.5ml
Antibody 1 x 6 ml
HRP-conjugate 1 x 6 ml
Wash Buffer
1 x 15 ml
（20×concentrate）
Substrate A 1 x 7 ml
Substrate B 1 x 7 ml
Stop Solution 1 x 7 ml
4
Standard S1 S2 S3 S4 S5
Concentration
（ng/ml）
0.5 1 2 5 10
STORAGE
1. Unopened test kits should be stored at 2-8°C upon receipt
and the microtiter plate should be kept in a sealed bag. The
test kit may be used throughout the expiration date of the kit,
provided it is stored as prescribed above. Refer to the
package label for the expiration date.
2. Opened test plate should be stored at 2-8°C in the aluminum
foil bag with desiccants to minimize exposure to damp air. The
kits will remain stable until the expiring date shown, provided it
is stored as prescribed above.
3. A microtiter plate reader with a bandwidth of 10 nm or less
and an optical density range of 0-3 OD or greater at 450nm
wavelength is acceptable for use in absorbance
measurement.
TECHNICAL HINTS
1. Bring all reagents and plate to room temperature for at least
5
30 minutes before use. Unused wells need store at 2-8℃and
avoid sunlight.
2. Wash Buffer If crystals have formed in the concentrate,
warm to room temperature and mix gently until the crystals
have compley dissolved. Dilute 15 ml of Wash Buffer
Concentrate into deionized or distilled water to prepare 300 ml
of Wash Buffer.
3. To avoid cross-contamination, change pipette tips between
additions of each standard level, between sample additions,
and between reagent additions. Also, use separate reservoirs
for each reagent.
4. When using an automated plate washer, adding a 30 second
soak period following the addition of wash buffer, and/or
rotating the plate 180 degrees between wash steps may
improve assay precision.
5. Substrate Solution should remain colorless or light blue until
added to the plate. Keep Substrate Solution protected from
light. Substrate Solution should change from colorless or light
blue to gradations of blue.
6. Stop Solution should be added to the plate in the same order
6
as the Substrate Solution. The color developed in the wells
will turn from blue to yellow upon addition of the Stop Solution.
Wells that are green in color indicate that the Stop Solution
has not mixed thoroughly with the Substrate Solution.
Precaution: The Stop Solution provided with this kit is an acid solution. Wear
eye, hand, face, and clothing protection when using this material.
OTHER SUPPLIES REQUIRED
Microplate reader capable of measuring absorbance at 450
nm, with the correction wavelength set at 540 nm or 570 nm.
Pipettes and pipette tips.
Deionized or distilled water.
Squirt bottle, manifold dispenser, or automated microplate
washer.
An incubator which can provide stable incubation conditions
up to 37°C±0.5°C.
SAMPLE COLLECTION AND STORAGE
Serum Use a serum separator tube （SST） and allow
samples to clot for 30 minutes before centrifugation for 15
minutes at 1000 x g. Remove serum and assay immediay
7
or aliquot and store samples at -20°C. Centrifuge t he sample
again after thawing before the assay.Avoid repeated
freeze-thaw cycles.
Plasma Collect plasma using citrate, EDTA, or heparin as
an anticoagulant. Centrifuge for 15 minutes at 1000 x g within
30 minutes of collection. Assay immediay or aliquot and
store samples at -20°C. Centrifuge the sample again after
thawing before the assay.Avoid repeated freeze-thaw cycles.
Note: Grossly hemolyzed samples are not suitable for use in this assay.
ASSAY PROCEDURE
Bring all reagents and samples to room temperature before use. It is
recommended that all samples, standards, and controls be assayed in duplicate.
All the reagents should be added directly to the liquid level in the well. The
pipette should avoid contacting the inner wall of the well.
1. Set a Blank well without any solution. Add 50µl of Standard or
Sample per well. Standard need test in duplicate.
2. Add 50µl of HRP-conjugate to each well （not to Blank well）,
then 50µl antibody to each well. Mix well and then incubate
for 3 hour at 37°C.
3. Fill each well with Wash Buffer （about 250µl）, stay for 10
8
seconds and Spinning. Repeat the process for a total of three
washes. Complete removal of liquid at each step is essential
to good performance. After the last wash, remove any
remaining Wash Buffer by aspirating or decanting. Invert the
plate and blot it against clean paper towels.
4. Add 50µl of Substrate A and Substrate B to each well, mix
well. Incubate for 15 minutes at 37°C. Keeping the plate away
from drafts and other temperature fluctuations in the dark.
5. Add 50µl of Stop Solution to each well when the first four
wells containing the highest concentration of standards
develop obvious blue color. If color change does not appear
uniform, gently tap the plate to ensure thorough mixing.
6. Determine the optical density of each well within 10 minutes,
using a microplate reader set to 450 nm.
CALCULATION OF RESULTS
Using the professional soft "Curve Exert 1.3" to make a standard curve is
recommended, which can be downloaded from our web.
Average the duplicate readings for each standard, Blank, and
sample and subtract the optical density of Blank. Create a
standard curve by reducing the data using computer software
9
capable of generating a four parameter logistic （4-PL） curve-fit.
As an alternative, construct a standard curve by plotting the
mean absorbance for each standard on the y-axis against the
concentration on the x-axis and draw a best fit curve through the
points on the graph. The data may be linearized by plotting the
log of the MBP concentrations versus the log of the O.D. and the
best fit line can be determined by regression analysis. This
procedure will produce an adequate but less precise fit of the
data. If samples have been diluted, the concentration read from
the standard curve must be multiplied by the dilution factor.
LIMITATIONS OF THE PROCEDURE
The kit should not be used beyond the expiration date on the
kit label.
Do not mix or substitute reagents with those from other lots or
sources.
If samples generate values higher than the highest standard,
dilute the samples with the appropriate Diluent and repeat the
assay.
Any variation in operator, pipetting technique, washing
technique, incubation time or temperature, and kit age can
10
cause variation in binding.
This assay is designed to eliminate interference by soluble
receptors, binding proteins, and other factors present in
biological samples. Until all factors have been tested in the
Quantikine Immunoassay, the possibility of interference
cannot be excluded.
環保在線 設計制作，未經允許翻錄必究 .? ? ?
請輸入賬號
請輸入密碼
請輸驗證碼
請輸入你感興趣的產品
請簡單描述您的需求
請選擇省份